Les fissures dans la substance du bâtiment sont des points faibles sur le plan structurel. En outre, la pénétration de l'eau peut causer des dommages et réduire l'utilisation et la durée de vie du bâtiment. Un colmatage élastique ou un collage structurel de la fissure est nécessaire. Pour ce faire, la fissure est remplie sur toute sa longueur avec une résine d'injection de polyuréthane par injection sous pression. Les résines d'injection appliquées peuvent également être utilisées dans les environnements d'eau potable.

Montrez les références

Injection de fissures par injection de pression sur des fissures sèches ou humides

Les fissures sèches ou humides sont étanchées durablement avec les matériaux d'injection KÖSTER.

Le KÖSTER 2 IN 1 est le matériau standard pour l'imperméabilisation des fissures. Le matériau forme une mousse au contact de l'eau et l'arrête en réagissant avec l'eau ou en la déplaçant. Une deuxième injection avec le même matériau imperméabilise la fissure de manière permanente et élastique.

Le KÖSTER IN 3 est utilisé pour le collage structurel d'éléments de construction fissurés ou endommagés. Le KÖSTER IN 5 est une résine d'injection polyuréthane à très faible viscosité et à très longue durée de vie en pot. Elle est particulièrement adaptée à l'injection dans des fissures très petites et fines.

KÖSTER Micro Grout 1C est un matériau d'injection minéral qui est idéal pour remplir les vides et les fissures de largeur moyenne. Le matériau dispose d'excellentes propriétés d'adhérence, même sur des supports humides. Il possède également une résistance à la compression très élevée après durcissement.

Toutes les résines d'injection KÖSTER sont installées avec la pompe d'injection KÖSTER 1C par l'intermédiaire de vannes d'injection appelées "Packers" dans la fissure. Différents packers sont disponibles en fonction de l'application. Les packers à impact KÖSTER "12" sont installés très rapidement et sont recommandés pour des pressions faibles à moyennes.

Les Packers et Superpackers KÖSTER sont utilisés pour toutes les applications de basse à haute pression.

Les KÖSTER One Day Site Packers sont équipés d'une valve supplémentaire qui permet de retirer la partie supérieure de l'obturateur directement après l'injection et d'obturer le trou. Le trou de forage reste étanche à la pression.

Il faut toujours respecter les spécifications des directives techniques correspondantes.

Injection sous pression de fissures contenant de l'eau

In case of water actively leaking from a crack a combination of KÖSTER IN 1 (very fast foaming after contact with water) and KÖSTER IN 2 (used for permanently sealing the crack) is applied.

KÖSTER IN 7 is also a very fast foaming injection resin which creates a permanently elastic seal. KÖSTER IN 7 needs to have contact with water to build foam and for curing.

All KÖSTER injection resins are installed with the KÖSTER 1C Injection Pump via injection valves called “Packers” into the crack. Depending on the application, different packers are available.

KÖSTER Impact Packers “12” are installed very quickly and are recommended for low to medium pressure.

KÖSTER Packers and KÖSTER Superpackers are used for all applications from low to high pressure.

KÖSTER One Day Site Packers have an extra valve so that the upper part of the packer can be removed directly after injection and the hole plugged. The borehole stays pressure sealed.

Always adhere to the specifications in the respective Technical Guidelines.

Waterproofing of construction joints in the wall/floor junction

For retroactive waterproofing of the wall-floor junction the boreholes have to be drilled transecting the construction joint. The borehole should be drilled approximately into the middle of the construction joint.

For this application KÖSTER Superpackers or KÖSTER One Day Site Packers are used. The injection is done with the KÖSTER 1C Injection Pump.

For this KÖSTER IN 5 can be used, which is a very low viscous polyurethane injection resin with a very long pot life. It will pass into the small and finest cracks along the construction joint.

In case of flowing water or when it is not certain if the crack is dry or wet KÖSTER 2 IN 1 is injected. It is injected twice 10 – 20 minutes apart to ensure that the joint is permanently and elastically sealed.

Always adhere to the specifications in the respective Technical Guidelines.

Construction joint injection via an injection hose

1 Injection hose

2 Injection Resin
KÖSTER IN 5

Construction joints, especially in the wall floor junction, when installed underneath ground level always need particular attention when it comes to waterproofing. Defects in this area are not uncommon. Before pouring the concrete for the rising wall, the injection hose is installed in the construction joint. Injection hoses are perforated or slotted. After the concrete has cured an elastically curing resin is pressure injected into the injection hose. The joint is now permanently elastically sealed and waterproofed.

For the application via injection hose KÖSTER IN 5 is the product of choice. It has a low viscosity and a long pot life. These two aspects are very important for the application so the product has enough time to enter the small and fine voids and doesn’t start to react during the injection.

Always adhere to the specifications in the respective Technical Guidelines.

 

 

 

Back

Top
Albania Austria Bosnia and Herzegovina Brasil Bulgaria China Croatia Czech Republic Denmark Finland Germany Ghana Greece Hungary Italy Japan Kazakhstan Kuwait Latvia Lebanon Macedonia Mexico Netherlands New Zealand Norway Panama Poland Portugal Romania Russia Senegal Serbia Slovakia Slovenia South Africa Spain Thailand Turkey Ukraine United Kingdom United States of America